Stay up to date with the latest
news from AMT Heating

Follow our blogs to find out the latest
news in the heating industry.

Recommended by 100% of our customers

Experience that matters:

Boiler Pressure Too High? What It Means and What to Do

High boiler pressure is usually caused by too much water in the system, often after a top-up, a filling loop that’s been left open or a worn expansion vessel. A small rise when the heating is running is normal. A gauge sitting in the red, or climbing close to 3 bar, isn’t. You can often bring it down safely by bleeding a radiator, but if it keeps creeping back up, our boiler service and repairs team can find the cause. It’s a common call once the heating is on full time in Epsom and Sutton.

What normal boiler pressure looks like

Most sealed heating systems are filled to around 1 to 1.5 bar when cold, but check your boiler manual for the exact figure. When the heating is on, the water expands as it warms, so the pressure rises a little. A rise of around half a bar when hot is typical on many systems.

The problem is when the pressure is already high when the system is cold, or when it climbs much higher once the heating has been running.

Common causes of high boiler pressure

Overfilling after a top-up

The most common cause. If the system was topped up past the recommended level, perhaps after bleeding radiators, it will run high. It’s an easy mistake to make, especially if the gauge is hard to read.

A filling loop left open or letting by

The filling loop connects your heating system to the mains water. If its valves aren’t fully closed, or one of them is worn and letting water through, mains water slowly pushes the pressure up over hours or days.

A failed expansion vessel

The expansion vessel is a small tank with an air cushion inside that absorbs the extra volume of water as it heats up. Over time it can lose its air charge. When that happens, the pressure jumps sharply as soon as the heating comes on, then drops again when it cools.

A pressure relief valve that’s started to pass

If pressure gets too high, the pressure relief valve opens to release water through a small pipe, usually to the outside. Once it has opened a few times, it may not seal properly, and you’ll see drips from that pipe.

A safe way to bring the pressure down

If the gauge is reading high, you can usually lower it by bleeding a radiator:

  1. Turn the heating off and let the system cool
  2. Put a towel under the radiator valve and hold a cloth or container ready
  3. Open the bleed valve slowly with a radiator key and let some water out
  4. Close it again and check the gauge
  5. Repeat in small steps until the pressure is back in the normal range

Also check that both taps or levers on the filling loop are fully closed. If you’re not sure what the filling loop looks like, check your boiler manual.

If the pressure has been too low instead, our post on why a boiler loses pressure covers the causes.

What needs a Gas Safe registered engineer

Leave these jobs to an engineer:

  • Recharging or replacing the expansion vessel
  • Replacing a pressure relief valve that keeps dripping
  • Repairing or replacing a filling loop that’s letting by
  • Anything that involves removing the boiler casing

If you notice water leaking from the boiler itself, turn it off and read our guide on why a boiler leaks water before you call.

High pressure problems in Worcester Park, Epsom and around Sutton

Many homes around Worcester Park, Epsom and Sutton have combi boilers that have been in place for a good number of years. Expansion vessels on older boilers are one of the parts most likely to have lost their charge, and the first cold weeks are when it shows, as the heating runs for longer and the pressure swings get bigger.

Frequently asked questions

Is high boiler pressure dangerous?

Boilers have safety devices, including the pressure relief valve, designed to release excess pressure before it becomes dangerous. Even so, running at high pressure puts strain on seals and valves and can lead to leaks. If the gauge is in the red or close to 3 bar, bring it down or get an engineer to look at it.

Why does my boiler pressure go up when the heating is on?

Water expands as it heats, so a small rise is normal. A large jump, followed by a drop as it cools, usually points to an expansion vessel that has lost its air charge. If you’re also seeing drips from the pressure relief pipe outside, that’s another sign the vessel needs checking.

How do I know if my filling loop is letting by?

If the pressure creeps up slowly even when the heating is off and nobody has topped it up, mains water is likely getting in through the filling loop. Check both valves are fully closed. If the pressure still rises, the loop or one of its valves may need replacing by an engineer.

Boiler pressure keeps climbing?

If you’ve brought the pressure down and it keeps creeping back up, get in touch and we’ll send an engineer to check the expansion vessel, valves and filling loop.