Stay up to date with the latest
news from AMT Heating

Follow our blogs to find out the latest
news in the heating industry.

Recommended by 100% of our customers

Experience that matters:

Heating Not Working but Hot Water Is?

If your taps run hot but the radiators stay cold, the boiler itself is usually working. The problem is normally in how it’s being asked for heat, or in the part that sends hot water to the radiators instead of the taps. Start with the thermostat and programmer settings, as they’re the most common cause. If those are fine, a stuck diverter valve on a combi or a zone valve on a system boiler is the likely culprit, and that’s a job for our boiler service and repairs team. We see this a lot in homes around Worcester Park and Sutton once the heating goes back on.

Why you can have hot water but no heating

A boiler does two jobs: heating water for the taps and shower, and heating water that flows round the radiators. On most systems, those two jobs share the same burner but take different routes through the pipework.

If hot water works, the boiler is lighting and the gas supply is fine. That narrows things down to the controls, or to the valve or pump that directs water to the radiators.

Safe checks you can make first

Work through these before calling anyone:

  • Thermostat: turn it up a few degrees above the room temperature. If it’s battery-powered or wireless, check the batteries and that it’s connected to the receiver.
  • Programmer or timer: make sure the heating channel is set to on, not just the hot water. Check the clock is correct after a power cut.
  • Smart controls: check the app hasn’t put the heating into away or holiday mode.
  • Radiator valves: make sure the valves on cold radiators aren’t turned off.
  • Boiler pressure: check the gauge. Many systems sit around 1 to 1.5 bar when cold. Low pressure can stop the heating while hot water still works on some models.

If the radiators are warm at the bottom but cold at the top, that’s trapped air, and bleeding them usually helps. Our post on why a radiator is cold explains what the different cold patches mean.

Common faults that need an engineer

A stuck diverter valve (combi boilers)

On a combi boiler, the diverter valve switches between hot water and heating. If it sticks in the hot water position, the taps work but the radiators never warm up. Sometimes the opposite happens and the radiators get warm when you run a hot tap.

A faulty zone valve or motorised valve (system and regular boilers)

On systems with a cylinder, a motorised valve opens to let water reach the radiators. If its motor fails or it sticks shut, the hot water still heats but the heating doesn’t.

A failing pump

If the pump is weak, it may manage the short hot water circuit but struggle to push water round the whole radiator system.

Wiring or control faults

A failed thermostat, receiver or wiring centre can stop the boiler getting the call for heat at all.

All of these involve working inside the boiler or on the system’s electrics, so leave them to a Gas Safe registered engineer.

When to call straight away

Turn the boiler off and get help if you see water leaking from the boiler, notice soot or staining, or your carbon monoxide alarm sounds. If you smell gas, turn off the supply at the meter if it’s safe, open the windows and call the National Gas Emergency Service on 0800 111 999.

Heating faults in New Malden, Worcester Park and around Sutton

Homes across south-west London and the Surrey border, from Victorian terraces in New Malden to 1930s semis and newer flats around Sutton, have a real mix of combi and system boilers. Valves and pumps that have barely been used all summer are often the first parts to stick when the heating comes back on in autumn. Older systems with sludge in the pipework are more prone to it.

Frequently asked questions

Why do my radiators get warm when I run the hot tap?

On a combi boiler, this usually points to a diverter valve that isn’t closing fully. Some of the hot water meant for the tap is passing into the heating circuit instead. It’s a common fault on older combis and normally needs the valve repairing or replacing by an engineer.

Can a power cut stop my heating but not my hot water?

Yes. After a power cut, programmers and timers can reset, lose their time settings or go back to a default where only hot water is on. Check the clock and heating settings first. Smart thermostats may also need to reconnect to the boiler or your Wi-Fi.

Is it expensive to fix a diverter valve?

It depends on the boiler and whether the valve can be repaired or needs replacing as a complete part. An engineer can usually diagnose it quickly. On a very old boiler with other faults building up, it’s worth asking whether the repair is still good value compared with a replacement.

Radiators still cold?

If you’ve checked the settings and the radiators still won’t warm up, get in touch and we’ll send an engineer to find the fault and get your heating working again.